ATAVRRZ200【PDF 21/22 页】KIT DEMO AT86RF230

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录52

17页 18页 19页 20页 [21页]22页

Demonstration Kit User Guide

6-3

5183AZIGB12/07/06

5. Go back to the Program tab, in the Flash section, browse to the location of the

input HEX file and select the filename: rz200_v1_0.hex. Press Program and ver-

ify that the process terminates successfully.

6. Alternatively, fuse settings can be altered using JTAG ICE mkII. In this case,

the Serial program downloading (SPI) enabled; [SPIEN=0] fuse must be

checked.

6.2.3

How to re-program

the RCB MAC

address

The 64-bit IEEE MAC address associated with the RCB is stored in the internal

EEPROM of the ATmega1281 that is on the RCB at address 0 (LSB). If the MAC

address has been inadvertently erased, the following steps can be followed to repro-

gram it into the EEPROM. This procedure should not be attempted if the RCB has a

valid MAC address. The following steps can only be performed with the JTAGICE mkII

while AVRStudio is running in Debug mode. This operation cannot be performed with

the AVRISP mkII included in your Demonstration kit.

The following steps reprogram the MAC address and MUST be completed from start to

finish once the program memory has been loaded (step 4), otherwise the RCBs MAC

address will be overwritten with all FFs.

1. Open AVR Studio.

2. Connect the JTAGICE mkII to the RCB programming header located on the Dis-

play Board.

3. From the File Menu, select Open File and open the file rz200_v1_0.hex from the

CDROM.

4. In the Save AVR Studio Project File dialog box, select Save to create a project

file.

5. In the Select Device and Debug Platform dialog box, select JTAGICE mkII as the

debug platform, ATmega1281 as the device, and then select Finish to start the

AVR Studio disassembler and load the program memory.

6. Enter drop menu Debug -> JTAGICE mkII Options

7. Select Debug tag

8. In the General area, select the Preserve EEPROM contents when reprogram-

ming device box and hit OK.

9. If the EEPROM Memory window is not already open: from the View tab, open

the active HEX files EEPROM contents by selecting EEPROM from the Memory

Window drop down list. The EEPROM memory window should contain all FFs.

10. Starting at location 0 (the upper most left corner of the window), enter the 16

byte MAC address printed on the back of the RCB PCB in reverse order.

Note: The MAC address MUST be written in reverse order in 2 byte pairs, i.e., if the

MAC address is 00-04-25-FF-FF-17-01-52, the sequence written into the

EEPROM must be entered as 52-01-17-FF-FF-25-04-00 from location 0. The

MAC address will automatically be saved to the EEPROM with each keystroke.

11. From the Project tab, select Close Project. You will be prompted to close and

end the debug session, select OK.

Caution: In the following step, you must select No. Selecting Yes will cause the MAC

address you just entered to be to permanently saved into the demokitfirmware.hex file.

This will make the file unuseable for other RCBs.

12. You will then be prompted to save the changes to demokitfirmware.hex. Select

No.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式